Spot tile repair or full resurfacing: how to choose in Thailand
Spot tile repair and regrouting make sense when the tilework is firmly bonded and only the joints have washed out or a few tiles have lifted. When tap-testing shows widespread hollow areas or failing render behind the tiles, stripping back to the shell is the practical choice.
Guides and answers · Search all guides
When spot repair and regrouting make sense
Spot repair and regrouting suit sound tilework with missing grout or localised loose or broken tiles. We check how far the damage extends and whether replacement tiles can blend with the existing finish. At the inspection we tap-test what we can reach; the full tap-test of the floor, walls, steps and waterline is done once the pool is drained, so the choice between spot repair and stripping back to the shell is confirmed at that point, and the work can go in stages.
We carry out all tile and grout repairs in a drained, dry pool because adhesives and grouts do not bond reliably to wet, algae-coated surfaces.
- Spot repairs: where damage is localised, we refix loose tiles or fit replacements if they can blend with the existing finish.
- Standard or epoxy regrouting: standard pool grout suits ceramic tiles and mosaics, while epoxy grout suits glass mosaic, steps, waterlines and busy hotel pools.
- Mosaic sealing: because small mosaic tiles have a small bonding area on ordinary adhesive, we can discuss regrouting combined with a sealing coat over the whole mosaic surface to bind it into one layer, provided the surface can be thoroughly dried. The coat binds the surface; it does not repair a failing render or waterproofing behind the mosaic.
When the tile bed needs full resurfacing
When we open up a failing tile bed, loose tiles are often a symptom of a problem in the render or waterproofing behind them. Patching one area tends to move the problem around the pool, so we recommend deep renovation: stripping the old tiles, render and every added layer back to the concrete shell.
With the concrete exposed, we repair cracks and weak joints, reset or replace fittings, waterproof where needed and render the shell through. You can then choose a seamless PebbleCrete finish, which has no grout joints to wash out, or new mosaic or large-format tiles.
Where a leak is one of the reasons for the strip-out, we first test the pipework under pressure and compare the water level with the pump on and off, so that a pipe leak is not mistaken for a leak in the shell. We cannot promise to find every leak without opening up parts of the structure.
- Tiles or mosaic coming away in patches, or sounding hollow over large areas
- Render or an old finish lifting off the wall, with loose fill behind it
- Layers added over earlier repairs, raising the surface and hiding the problem
- Leaks through the shell, joints or fittings that cannot be reached without taking the surface off
Inspection and planning the shutdown
Start with an inspection and plan the shutdown around your bookings. You receive a written report with photos and priorities, usable with any contractor. If structural damage appears, we agree the next step with you and your engineer — or, if you don't have one, with our partner engineer. Hidden problems may emerge when the pool is opened up.
Tile, grout and resurfacing work need an empty pool. We organise draining, cleaning, refilling and start-up water balancing as part of the job. Source water, equipment, use and the finish all matter, and testing is done on site.
Draining needs care in the wet season or where groundwater is high: an empty shell can be lifted or cracked by groundwater pressure, and a damp shell is slower to dry for tile and grout work. We check the site and the season before draining and agree the timing with you.
Further reading
How we can help
Regrouting & tile repair
Missing grout and loose mosaic tiles trap dirt, leave sharp edges and let water reach the render beneath. We drain the pool to regrout tilework and replace broken tiles.Deep renovation & resurfacing
When the tiles, render or an old finish fail across a pool, patching tends to move the problem around. We strip the pool back to the shell, removing the old tiles, render and every added layer. Then we renew it in PebbleCrete or with new tiles.Pool inspection and report
We visit your pool, inspect it closely and send you a written report with photos and our recommendations in order of priority. The report is yours to use with any contractor.Where we have done this
- Mai Khao Dream Villa Resort — We raked out the old grout, fixed loose mosaic, then regrouted and laminated the pools. We also brought the main pool jacuzzi system back into service.
- Crest Resort & Pool Villas — Because the old build-up and layers were lifting off the wall with fill behind them, each pool was taken back to sound concrete and refinished in PebbleCrete Supreme Verde with PebbleCrete Glass Sea Mist Green on the coping.
- Private Residence, Bang Tao — failing mosaic replaced — The small blue mosaic had started to lose tiles, so it was chipped off the walls and floor, the shell was rendered and prepared, and a new finish was laid through the pool and steps.
Questions we are asked
Can you regrout or fix loose tiles underwater without draining?
No. Adhesives and grouts do not bond reliably to wet, algae-coated surfaces. We drain and dry the pool so the adhesive and grout can bond properly.
Spot tile repair or full resurfacing: how do we choose?
If tap-testing shows the tilework is firmly bonded and only the joints have washed out or a few tiles have lifted, spot repair and regrouting are enough. If hollow areas, lifting render or leaks through the shell are widespread, patching only moves the problem around, so we recommend stripping back to the shell. Hidden problems may only show once the pool is drained, so the choice can be confirmed in stages.
Why do tiles keep coming off in patches after earlier repairs?
Widespread delamination usually points to water behind the tile bed, failed waterproofing or failing render. Patching tends to move the problem around the pool, so stripping the surface back to the shell is recommended.
Can we retile the pool instead of using PebbleCrete after a strip-out?
Yes. Once the old tiles, render and added layers are removed and the shell is re-rendered, the pool can be finished in PebbleCrete or with new tiles.
Related guides
Pool tiles coming loose in Phuket: causes, inspection and repair options
In Phuket, pool tiles usually come loose for a few reasons: daily heating at the waterline, water that slowly dissolves cement grout, movement in the shell or terrace, bedding that has aged, and earlier repairs that did not hold. Open joints then let water into the bed behind the tiles. This guide explains what an inspection looks at and how to choose between spot repair, regrouting and taking the pool back to the shell.Can a new pebble or glass pool finish go over existing tiles?
No — before we apply a PebbleCrete pebble or glass finish, we strip the old tiles, the render and every added layer back to the concrete shell. Laying a new finish over old tilework raises the surface and hides problems in the bed, render or waterproofing beneath.When to renovate a hotel or resort pool in Thailand: seasons, rain and keeping the hotel open
In Thailand, hotels and resorts keep busy periods clear by doing pump room, surround and waterline work with the pool open, and save drained shell renovations for quieter booking windows — timed around the rains and the site's groundwater, because an open shell needs dry conditions. Starting with an on-site inspection lets you separate urgent repairs from planned shutdowns.Is a pebble or glass pool finish rough on bare feet?
A PebbleCrete pebble or glass finish is textured and feels different underfoot from smooth glazed tile. We bring samples so you can feel the surface before choosing a finish for floors, steps, ledges or seating.Tell us where the pool is and what you want changed.
Send photos → discuss the work → site assessment if needed → quotation
Call 089 277 3314Email photos of your poolAdd us on LINE
