Can a new pebble or glass pool finish go over existing tiles?
No — before we apply a PebbleCrete pebble or glass finish, we strip the old tiles, the render and every added layer back to the concrete shell. Laying a new finish over old tilework raises the surface and hides problems in the bed, render or waterproofing beneath.
Guides and answers · Search all guides
Why we strip the pool back to the shell
We strip the pool back to the shell to expose problems beneath the tiles before applying a new finish. Old tiles, render and added layers come off so we can inspect the concrete, repair cracks and weak joints, and prepare new render for PebbleCrete or tiles.
When tiles come away in patches or sound hollow, the fault usually lies in the adhesive, the render or the waterproofing beneath. Stripping the pool to the concrete shell lets us deal with the cause first.
- Remove the old tiles, the render and every layer added since the pool was built
- Expose the concrete shell to repair cracks and weak joints
- Reach leaks through the shell, joints or fittings that cannot be reached with the old surface in place
- Reset or replace fittings, waterproof where needed and render the shell through for the new surface
When to repair existing tiles instead
Repairing existing tilework suits pools where most tiles are sound and damage is localised, or where grout needs renewing. We inspect the pool, tap-test accessible surfaces, check grout joints and look for signs of leaks before recommending repairs or stripping the pool back to the shell.
If the shell itself shows structural damage, we say so and agree the next step with you and your engineer — or, if you don't have one, with our partner engineer.
Not every hidden problem can be found before the strip-out, especially when a pool's history is unknown: some only appear once the tiles are off, and we cannot promise to find every leak before the surface is removed. The work can therefore go in stages, and we agree each stage with you.
- Regrouting and tile repair: when the tiles are sound and only grout is missing or a few tiles are loose, we repair and regrout the existing tilework in a drained pool using standard pool grout or epoxy grout
- Deep renovation to the shell: when tiles or render are failing over large areas, we strip the pool back to the shell, re-render and renew it in PebbleCrete or with new tiles
What to send for a first discussion
Send photos of the pool and damaged areas, your property location, approximate pool dimensions and whether the shell is concrete or fibreglass. Tell us whether you prefer PebbleCrete or tiles and what other work you want discussed. These details help us arrange an inspection and prepare a quotation.
- Photos of the pool, with close-ups of loose tiles, hollow areas or lifting render
- Your villa, hotel or resort location in Phuket or elsewhere in Thailand
- The approximate pool dimensions and whether the shell is concrete or fibreglass
- Whether you prefer PebbleCrete or tiles, and any other work you want included
Further reading
How we can help
Deep renovation & resurfacing
When the tiles, render or an old finish fail across a pool, patching tends to move the problem around. We strip the pool back to the shell, removing the old tiles, render and every added layer. Then we renew it in PebbleCrete or with new tiles.Regrouting & tile repair
Missing grout and loose mosaic tiles trap dirt, leave sharp edges and let water reach the render beneath. We drain the pool to regrout tilework and replace broken tiles.Pool inspection and report
We visit your pool, inspect it closely and send you a written report with photos and our recommendations in order of priority. The report is yours to use with any contractor.Where we have done this
- Private Villa, Naithon Beach — Royal Blue — The old tiles came off, the shell was surveyed point by point, and the pool was refinished in PebbleCrete Supreme Royal Blue with PebbleCrete Glass Nightfall Pearl on the coping, surround and entry ledge.
- Guesthouse, Kathu — The old tiles and floor mosaic were removed, the floor and walls prepared, cracks in the overflow repaired, and the pool refinished in PebbleCrete Classic Cool Blue and PebbleCrete Glass Andaman Blue.
Questions we are asked
Can you seal over small mosaic tiles instead of stripping them?
Where small mosaic tiles are sound and the surface can be thoroughly dried, we can discuss regrouting combined with a sealing coat to bind the mosaic into one layer. That is a repair option for sound mosaic, not a way to lay a PebbleCrete finish over old tiles.
Does the pool have to be drained?
Yes. The strip-out, the render and the new finish are all carried out in a drained, dry pool. We also drain and dry the pool for regrouting and tile repairs so adhesives and grouts bond reliably. Where groundwater is high or the monsoon is on, we check the groundwater level and the timing before draining: an empty shell can be pushed up or cracked by water pressure from below, and a wet shell is hard to dry.
Can other work be done while the old tiles are stripped?
Yes. With the pool empty and open, we often rebuild steps, replace old lights with ultra-slim resin-filled surface lights, add fibre optics, renew the coping and rework the pump room in the same shutdown. Any electrical work is agreed with your electrician or engineer.
Can a new pebble or glass pool finish go over existing tiles?
No. We strip the old tiles, the render and every added layer back to the concrete shell, repair cracks and weak joints, waterproof where needed and render the shell through before a PebbleCrete pebble or glass finish goes on. Laying a new finish over old tilework would raise the surface and hide problems in the bed, render or waterproofing beneath.
Related guides
Spot tile repair or full resurfacing: how to choose in Thailand
Spot tile repair and regrouting make sense when the tilework is firmly bonded and only the joints have washed out or a few tiles have lifted. When tap-testing shows widespread hollow areas or failing render behind the tiles, stripping back to the shell is the practical choice.Pool tiles coming loose in Phuket: causes, inspection and repair options
In Phuket, pool tiles usually come loose for a few reasons: daily heating at the waterline, water that slowly dissolves cement grout, movement in the shell or terrace, bedding that has aged, and earlier repairs that did not hold. Open joints then let water into the bed behind the tiles. This guide explains what an inspection looks at and how to choose between spot repair, regrouting and taking the pool back to the shell.When to renovate a hotel or resort pool in Thailand: seasons, rain and keeping the hotel open
In Thailand, hotels and resorts keep busy periods clear by doing pump room, surround and waterline work with the pool open, and save drained shell renovations for quieter booking windows — timed around the rains and the site's groundwater, because an open shell needs dry conditions. Starting with an on-site inspection lets you separate urgent repairs from planned shutdowns.Is a pebble or glass pool finish rough on bare feet?
A PebbleCrete pebble or glass finish is textured and feels different underfoot from smooth glazed tile. We bring samples so you can feel the surface before choosing a finish for floors, steps, ledges or seating.Tell us where the pool is and what you want changed.
Send photos → discuss the work → site assessment if needed → quotation
Call 089 277 3314Email photos of your poolAdd us on LINE
